|
 Fasteners
Steel Framing
No. 7 Square Drive Trim Head Self Drilling 410 SS
No.10 Phillips Drive Flat Head Self Drilling 410 SS
No. 6 Square Drive Flat Head Self Drilling 410 SS
No.10 Square Drive Pan Head Self Drilling 410 SS W/ Neoprene Sealing Washers
Wood Framing or Plywood
No.10 Phillips Drive Flat Head Type A 18/8 SS
No. 6 Phillips Drive Flat Head Type A 18/8 SS
Note: Fastener heads can be painted to match panels for flush countersink installation. A variety of fasteners and rivets can be provided.
|
 Countersink Tools
- No. 6 Diamond CSK/Masonry Drill
- No. 10 Diamond CSK/Masonry Drill
- Trim Hd Diamond CSK/Masonry Drill
 Patch Kits
Factory Supplied Color Matched Hole Filler
This material has been carefully formulated to match the physical characteristics of Petrarch panels and, if used in accordance with the instructions provided, will satisfactorily disguise the screw head.
|
|
 Bond Breaker Tapes
PVC Foam Tape, 1/8T X 1-1/2"W X 100'L (for use as thermal break or bond break)
Polyethylene Film Tape, 5milT X 1-1/2"W X 108'L (for use as bond break only)
|
 Neoprene Gasket
Vertical Joints: 1-3/8" Wide X 65LF Rolls
Corner Joints: 2-3/8" Wide X 65LF Rolls
Available in Grey or Black
|
 Aluminum Moldings
Finishes: Mill; Clear or Bronze Anodized; or Kynar painted. (All moldings are available in 12 ft. lengths.)
|
 PVC Joint & Corner Gasket - 41 LF Rolls
- Top Hat Divider
- Outside Corner
- Inside Corner
Standard Colors: Mid Brown, Light Grey, Mid Grey, Dark Grey, Buff, Cream, Brick Red, Bright Green, Black, and White.
|
|  System TEN66 Accessories
- Single Bracket - SB2, SB5, SB6
- Double Bracket - DB2, DB5, DB6
- IPS - Insulator Pad-Single
- IPD - Insulator Pad-Double
- "T" Rail (100/40 and 100/60)
- "L" Rail (60/40)
To view System TEN66 Accessories (Click Here)
|
 Structural Silicone Setting System
- SH-01 (4774S) Horizontal Head Plate
- SH-11 (4777S) Horizontal Stack Plate
- SH-21 (4778S) Horizontal Base Angle
- SV-51 (4775S) Vertical Joint Plate
- SC-201 (4776S) Inside/Outside Corner Angle
- To view above Bearing Plates (Click Here)
- E-595 Outside Round Corner (Click Here)
No. 8 X 1-1/2" Phillips Drive Pan Head Tek 410 SS (for attaching Bearing Plates to substrate)
1/8"T X 11/32"W X 6"L Silicone Setting Blocks
|
 Rain Screen System Profiles
To view all of the above extrusions (Click Here)
Handy CEP Extrusion Order Form (Click Here)
Finishes: Black Anodized and sealed. (All extrusions are available in 10 ft. lengths.)
Fastener Selection Guide (Click Here)
|
 Mechanical Back Fastened System (7/16" Panels Only)
- 1/8"T X 1"W X 5"L Flat Aluminum Bracket
- 1/8"T X 2"W X 2"L (each face) Angle Aluminum Bracket
- Fischer Expanding Brass Inserts, PA4 M6 X 7.5mm for 7/16" panels
- M6 X 12mm Hex Head Stainless Steel Machine Screw with washer
- Board Anchor Drill
In all cases, inserts are supplied installed in the rear of the panels with brackets and set screws packed separately.
|
| |
|
| |
|
| |
|
| |
|
| |
|
| |
|
| |
|